Beiträge: 32.116
Themen: 224
Registriert seit: May 2007
Bewertung:
178
Bedankte sich: 6765
7070x gedankt in 5843 Beiträgen
20.09.2018, 15:49
(Dieser Beitrag wurde zuletzt bearbeitet: 14.01.2019, 16:15 von Broadcasttechniker.)
Theoretically this could work.
But i don't know whether that works in real life.
With the respective pistons in the top dead center, but low in the liner you could be able to acces or at least inspect the places in question.
Changing or adding the O-ring should also work.
I would not go further than exposing the small end bearing.
The moment the oil scraper ring slips out of the liner you've lost.
Or better said, you've won the oilpan dismantling.
Imho there is no space to refit the ring.
Geteiltes Wissen ist doppeltes Wissen
Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
So it means I can press a piston into a liner from above but I cannot put a liner over a piston from above because I can't reach the rings to compress them, right?
So I must first remove the oil pan, remove the piston from above, then I put the liner and then press the piston from above.
Beiträge: 2.472
Themen: 8
Registriert seit: Jul 2016
Bewertung:
8
Bedankte sich: 40
614x gedankt in 525 Beiträgen
And take a look page 57 of the manual.
Its not good at all to overhaul without it.
Beiträge: 32.116
Themen: 224
Registriert seit: May 2007
Bewertung:
178
Bedankte sich: 6765
7070x gedankt in 5843 Beiträgen
20.09.2018, 16:15
(Dieser Beitrag wurde zuletzt bearbeitet: 20.09.2018, 16:21 von Broadcasttechniker.)
When I did this, I had to remove all 4 liners WITH THE PISTONS IN THEM.
I did NOT pull the pistons, they always were in place.
Keep the piston/liner assy in their place, i.e. 1 in 1, 2 in 2 and so forth.
There is a left right, so don't turn them 180 degrees.
Read the manual!
I think there will "only" be debris/rust on the liner seating.
Geteiltes Wissen ist doppeltes Wissen
Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
I found out the liners can't go out from above when the piston is in place, the liners are narrower then the piston at their bottom. I most push the pistons from the bottom after removing the big ends.
What do you think I should replace with new if I'm already taking pistones out?
Beiträge: 32.116
Themen: 224
Registriert seit: May 2007
Bewertung:
178
Bedankte sich: 6765
7070x gedankt in 5843 Beiträgen
No.
In this case I'd replace the motor with an other one.
Geteiltes Wissen ist doppeltes Wissen
Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
I wish I have watched it before:
Beiträge: 32.116
Themen: 224
Registriert seit: May 2007
Bewertung:
178
Bedankte sich: 6765
7070x gedankt in 5843 Beiträgen
Its good for you because its in English, but there are no differences between the video and the shop manual.
Geteiltes Wissen ist doppeltes Wissen
Beiträge: 32.116
Themen: 224
Registriert seit: May 2007
Bewertung:
178
Bedankte sich: 6765
7070x gedankt in 5843 Beiträgen
23.09.2018, 18:26
(Dieser Beitrag wurde zuletzt bearbeitet: 23.09.2018, 18:30 von Broadcasttechniker.)
As far as I know you don't have to open the cooling circuit when removing the AC compressor.
Look at my pictures. But I have to admit that it was the D7F
http://www.twingotuningforum.de/thread-6...pid8426590
If you lost the gas "with an explosion" make shure that you top up compressor oil.
As for the pictures.
Please don't attach them.
Please don't host them outside the forum.
Please upload them with this internal tool
https://pics.twingotuningforum.de/
I fixed the picture with the sump.
Geteiltes Wissen ist doppeltes Wissen
Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
Maybe in the d engine it's possible. There was no way I could take the c3g sump without moving down the compressor. It was blocked. Regarding the picture, l tried to upload here but it's limited to 500kb.
Beiträge: 32.116
Themen: 224
Registriert seit: May 2007
Bewertung:
178
Bedankte sich: 6765
7070x gedankt in 5843 Beiträgen
No, its not limited.
Please, use the link supplied
https://pics.twingotuningforum.de/
Why couldn't you move the compressor?
I must admit that Idon't know the C3G engine with AC.
This was one
http://www.twingotuningforum.de/thread-7920.html
Geteiltes Wissen ist doppeltes Wissen
Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
I moved the compressor only after I disconnected it from the gas lines. The compressor blocks the sump. I can show you if you want.