Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
ok, I see in the parts diagram it is connected properly.
Beiträge: 2.463
Themen: 8
Registriert seit: Jul 2016
Bewertung:
7
Bedankte sich: 40
609x gedankt in 521 Beiträgen
Cross is for a C063 Twingo and not in stock anymore.
Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
Are there any torque specs for the exhaust nuts and studs? and for the pump bolts and temp sensor plate? and valve cover?
Beiträge: 2.463
Themen: 8
Registriert seit: Jul 2016
Bewertung:
7
Bedankte sich: 40
609x gedankt in 521 Beiträgen
studs and nuts are hand tighten, (limited windings ).
water pump 18 , valve cover 12, temp sensor probably 20 .
Always check for leaks after warm up.
Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
I think 18NM is too much for the water pump and temp sensor plate. I broke 3 bolts and stripped one thread.
Beiträge: 2.463
Themen: 8
Registriert seit: Jul 2016
Bewertung:
7
Bedankte sich: 40
609x gedankt in 521 Beiträgen
new bolts ? sorry for that. Your torque wrench is exactly calibrated ?
Next time torque by hand.
Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
No, old bolts broken but when I put a new one, the thread got damaged, it wasn't a big issue, but I kept the plate of the temp sensor on 11NM.
When I tried to put the head over the gasket, The gasket moved and got scratches and bent, do you think I can still use it?
Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
I don't know how to keep the gasket in place while putting the head back on, it's heavy and I've already ruined one gasket.
Beiträge: 2.463
Themen: 8
Registriert seit: Jul 2016
Bewertung:
7
Bedankte sich: 40
609x gedankt in 521 Beiträgen
I cannot help at all, but firstly, the gasket is self adhesive,
secondly, you need to put in 2 headless bolts to guide the cylinder head.
Wish you luck, its seems not at hand right now.
Normally, documents should guide your actions.
Beiträge: 32.001
Themen: 224
Registriert seit: May 2007
Bewertung:
168
Bedankte sich: 6721
7004x gedankt in 5790 Beiträgen
Geteiltes Wissen ist doppeltes Wissen
Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
I did it. You have to be careful and only lower the head over the gasket vertically. I used 2 drill bits to make sure the gasket is locked in place in 2 corners, I removed one of them by hand and one of them from the head hole with tweezers.
Beiträge: 256
Themen: 27
Registriert seit: Jun 2018
Bewertung:
0
Bedankte sich: 28
22x gedankt in 18 Beiträgen
Any torque specs for spark plugs? Exhaust pipe 2 nuts?